Minggu, 30 Juni 2013

Error Code Canon Ir4570

Product : imageRUNNER 4570 series
Title : E000
Error : There were several symptoms

1st symptom was an intermittent error code of  E000, sometimes the machine would run as many as 20k before the problem would re-occur.

2nd symptom was the fixing film could be caked with toner.

3rd and most common symptom was that the latch would catch when opening the Main Right Side Door, this can be remedied by adjusting the cover that can interfere with the fuser release (1 screw ) (this cover is added when installing the internal finisher).  The common mistake in the field is to bend this latch instead of adjusting the cover.

Workaround :
Problem was that the latch that releases and applies pressure to the fixing film had been bent causing this mechanism to work erratically (proper and improper pressure when the Main Right side door was closed ).

Solution was to replace the latch which is formally called the Hook Holder Unit;

Part # FM2-0355-000
Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E001 Error Code That is Not Resetable
Error :
When the machine powers up the E001 error code is displayed but cannot be reset.  (Note: The reset procedure for an E001 code is COPIER>FUNCTION>CLEAR>ERR)

Workaround :
In this case, the Main Power Supply PCB Assembly was replaced.  The machine was powered up and the E001 code was able to be reset.  The part number for the Main Power Supply Assembly is FM2-0260-000.

Remember, if the fixing unit circuitry has an open or a short, the code may not reset.  Be sure to confirm the fixing unit wiring and try resetting the code before replacing the Main Power Supply Assembly


Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E004 Error Code
Problem :
The imageRUNNER 2270 / 2870 / 3570 / 4570 displays an E004 code. Replacement of the fuser assembly and clearing of the error code in service mode resolves the issue. After approx. one day of operation the E004 code returns. Inspection of the fuser reveals that the ceramic heater element has cracked into two or more pieces with apparent arcing from the heater element.

Solution :
To resolve this reoccuring error code it is necessary to cut all the wire ties on the wire harness running from the fuser assembly to the DC-CON PCB and Power Supply.

Product :imageRUNNER 2230/2230G/2270/2830/2870/3025/3030/3035/3045/3530/3530G/3570/4570 Title : E014-0001
Error :
E014-0001 was indicated upon start-up or when pressing the Start button. E014-0001 can be an indication of a faulty fixing motor. E014-0001 can be displayed when the drive detection signal is absent for 2 sec although detection is executed every 100msec after the start of motor rotation.


Workaround :
1. Check the fixing unit for binds or broken parts.
2. Re-fit J311, and J319 connectors of the DC Controller PCB.
3. Re-fit J1009 and J1011 connectors of the fixing motor.
4. If the symptom still occurs, replace the fixing motor with a new one.

The part number for the Fixing Motor is FK2-0367-000.
Product : imageRUNNER 2270 / 2870
Title : E020 Error Code

Problem :
E020 when copying. The sub-hopper motor M12 would not turn on in service mode or when running copies. As a result, the developing assembly would run out of toner. Tried replacing the Hopper Assembly, Developing Assembly and DC Controller with no change.

Solution :
Replace the Controller Power Supply PCB.  This PCB provides 3.3v, 5v, 13v and 24v to the DC Controller.  The part number is FM2-2764-000. It is item 15, shown below, and is located behind the Accessories Power Supply.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Title :E020-0000
Error :
The E020-0000 Error Code will occur if there is an absence of toner detected by the Developing Assembly Toner Level Sensor and a presence of toner is detected by the Hopper Toner Level Sensor.  The error code will be displayed after a specified period of time with the sensors detecting this condition.

Workaround :
The output of the sensors can be checked at the DC Controller PCB.  In this case, the sensors output indicated toner in all areas of the developing assembly.  The DC Controller was replaced and resolved the E020-0000 Error Code.

Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E020-0000 Error Code
Error :
E020-0000 Error Code will occur if there is an absence of toner detected by the Developing Assembly Toner Level Sensor and a presence of toner is detected by the Hopper Toner Level Sensor.

Workaround :
In this case, a small piece of plastic from the toner bottle was found lodged in the developer unit auger.  With the auger blocked, the toner would not properly move to the sub hopper.  The plastic piece was removed and the toner in the developer unit was vacuumed out to prevent further contamination.  Inspection of the toner motor drive and the auger mechanism for any foreign object damage is recommended before installing a new toner bottle.

Product : iR 4570 series
Title : E024
Error :
E024-0001 Error Code: The toner level sensor has an open-circuit or is not connected.


Workaround :
E024-0001 Error Code:

Toner gets in the developing assembly toner sensor (TS1) and may be shorting out the sensor. Blow out any toner in the sensor wiring and check to see if measure resolved the symptom. The toner level sensor has an open-circuit, replace the toner sensor.
Toner Sensor  FK2-0358

However, re-attachment of the sensor also solves the symptom.

When the symptom has occurred, make the following selections in service mode [COPIER > I/O > DC-CON] and check the setting for the bit1 of [P021]. If the setting is "1", re-attach the toner sensor.

Product :imageRUNNER 2230 / 2230G / 2270 / 2830 / 3025 / 3030 / 3035 / 3045 / 3530 / 3530G / 3570 / 4570,  Finisher S-1
Title : E024 on an imageRUNNER 2230/2270/3025 series machine.
Error :
E024 on an imageRUNNER 2230/2270/3025 series machine.

Workaround :
One problem  found has been the toner sensor scraper blade in the developer not making contact with the surface of the toner sensor.  To check the toner sensor scraper blade first set up a work area.  Lay out several sheets of 11 x17 paper on the work surface.  Disassembling the developer is a messy job.  Remove the upper cover of the developer and then rotate the developer in a counter clock wise direction.  Basically the cylinder should rotate so the toner is scraped off of the cylinder by the developer blade.
If it is rotated in the wrong direction a large amount of toner will adhere to the developer cylinder and makes a mess.
The toner sensor is located on the on the outside of the developer and part of it goes through the wall of the developer unit.

Product : imageRUNNER 2230/2270/2830/3870/3530/3570/4570
Title : Error E064-0002

Error : E064-0002
The machine displays an E064-0002. The machine creates solid black copies/internal test prints from edge to edge without any blanking.

Workaround :
Check the physical connections of the primary contacts. The primary drum contact is located on the drum and makes contact with an HVT metal contact on the machine's rear. The drum's primary contact tab can be easily bent or deformed during drum replacement or removal. If it becomes bent it can cause solid black copies creating a voltage leak also causing an E064-0002. Before replacing the high voltage power supply check the contact tabs first. Reshape the contacts or replace the drum.

Product : imageRUNNER 2230 / 2230G / 2270 / 2830 / 2870 / 3530 / 3025 / 3030 / 3035 / 3045 / 3530G / 3570 / 4570
Title : Error E064-0003
Error : E064-0003

Workaround :
The E064 code with a 0003 sub code can occur if Toner gets on the Developing Bias Tab.  If  the Toner is getting on the Developing Bias Tab you should check the seal on top of the Developer.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E100 - 0001 and E110 - 0002
Problem :
The machine is displaying error code E100 sub code 0001 and E110 sub code 0002.  The E100 - 0001 indicates that the BD interval is outside a specified range.  The E110 -0002 indicates that the scanner motor of the laser is faulty.

The laser unit and DC controller were replaced.  The wiring for the laser unit was checked.

Solution :
The problem was that the grounding spring for the steel registration roller was not making contact with the roller.  Reformed the spring so that it made contact with the roller and the error code issue was resolved.  Please see the photo below.  The grounding spring is circled in red.
Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E100 or E110 is Shown on the Display
Error :
E100 or E110 is shown on the Display. The error points to a Laser or Laser Shutter issue. After inspecting all Laser related item it was found that the Ground Plate for the Registration Roller was not making contact.

Workaround :
Check that the ground tabs are touching the Metal Registration Roller correctly

imageRUNNER 2230 / 2830 / 3530
Title : E100, E110 Error Codes
Error :E100, E110

Workaround :
Although the Main Power Supply, Controller Power Supply, DC Controller, Laser, and Drum, were replaced for this issue, the Accessories Power Supply Pcb. resolved the problem (Part number FK2-0338-000).

Product : imageRUNNER 2270/ 2870 / 3570 / 4570
Title : E100-0001 Error Code
Problem :
The machine is displaying an E100-0001. Cleared RCON, DCON and MMI. Cut tie-wraps. The DC Controller, Laser Assembly, Main Controller, Hard Drive, Memory, Boot ROM, All Night Power Supply, Controller Power Supply and wiring harnesses to the laser were replaced with no change. Checked the laser shutter.

Solution :
When the DC Controller was replaced, the original DCON ROM was reused.

Flashed the DCON firmware and resolved the problem.
Product : imageRUNNER 3025 / 3035 / 3045 Title : E110-0001 / 0002 IntermittentProblem :
Very intermittent E110-0001 / 0002, on copies 1 code in about 150 copies. The  DC Controller, Laser, Power Supply and Main Controller have been replaced with no change in error code.

Solution :
While in process of replacing 2nd Laser assyembly, found a cut on two wires in harness to Laser causing a short circuit. Harness was repaired with electrical tape.

Product : imageRUNNER 2230 / 2830 / 3530
Title : E111 Error Code when Flashing the Machine Problem :
When trying to flash the machine, the service support tool displays an E111 error. There is also a message that says "Necessary data not found bpchost.cha files \ servicesupporttool \ bpchost.cha".

Solution :
Multiple versions of the service support tool were installed on the laptop. It is important to uninstall previous versions of the service support tool before installing a new verison of the tool.

Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3530 / 3570 / 4570
Title :E190 and E240 Error Codes in Service Support Tool when trying to Format HDD
Problem :
After replacing the HDD, the Service Support Tool is alternately displaying E190 and E240 error codes.

Solution :
After reseating connections on the Main Controller, it was discovered the contacts on the Boot Rom were dirty. After cleaning the contacts on the Boot, as well as the socket on the Main Controller, the HDD was able to be formatted, and all files installed.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E191
Problem :
The machine was giving an error code of E191 which indicates an error with communication with the high-voltage power supply.  Replaced the high-voltage power supply and the DC controller pcb with no change.

Solution :
The wiring between the DC controller and the high-voltage power supply was broken.  Replace the high voltage connect cable.  Part number FM2-2819-000.  The cable is item 9 circled below.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570
Title :E191 Error Code
Error :E191 Error Code


Workaround :
Check for a pinched wire in the harness from Connector J404 of the High Voltage Power Supply PCB to the rear frame connector of the ImageRunner, J4001. It may be necessary to replace the High Voltage Power Supply PCB (part number: FM2-0261-000).

Please note: currently, there is no part number for the affected wiring harness
Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E225 Occurs During the Power Up Sequence
Problem :E225 Occurs During the Power Up Sequence

Solution :
In this case, the platen glass had been reversed when being cleaned by the technician.  Make sure the platen glass has the red arrow in the rear left corner of the machine top plate.  As indicated in the picture below, the red arrow should be right above the CIS ribbon cable when the glass is installed correctly.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E227-0001
Problem :E227-0001 & all 24 volts are missing in machine.


Solution :
E227-0001 was caused by Main Power Supply not putting out correct voltage at J1303. After installing new Main Power Supply {FM2-0260-000} machine worked with no problems.

Product : imageRUNNER  2230 / 2230G  /  2270  /  2830  /  2870  /  3025  /  3030  /  3035  /  3045  /  3530  /  3530G  /  3570  /  4570
Title : E240 Error only on Duplexing.
Error :E240 Error only on Duplexing. The imagerRUNNER will also lock up when the code occurs.Simplex copying works fine.

Workaround :
In this case CL6, Duplex Clutch was faulty. You can check the Duplex Clutch in Service mode in Parts check, CL > 4.

Product : imageRUNNER 3025 / 3030 / 3035 / 3045
Title : E261-0000 Error Code
Problem :
The Service Manual notes this issue as the Zero-Cross signal not detected for 500msc or more after the relay is on.

Solution :
In this case, by replacing the Main Power Supply Assembly ( FM2-0260-000 ) corrected the issue.

Product : imageRUNNER 3025 / 3030 / 3035 / 3045
Title : E261-0000 Error Code
Problem :
The Service Manual notes this issue as the Zero-Cross signal not detected for 500msc or more after the relay is on.

Solution :
In this case, by replacing the Main Power Supply Assembly ( FM2-0260-000 ) corrected the issue.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E291 - Network Connection Problems
Problem :
When trying to update the system software the laptop displayed the following message in the Service Support Tool interface.

E291

Check if the PC is connected to the network.
Socket Error Number:10065
Socket Error Description: No route to host.
File Name: Target Info.txt


Solution :
The laptop could ping the imageRUNNER and yet the E291 code would display when trying to download the system software.  In this case, the main controller clear was performed. (COPIER>FUNCTION>CLEAR>MN-CON)  Then, a successful system software update was able to be completed.

Note: When performing an MN-CON clear you should first generate a p-print.  (COPIER>FUNCTION>MISC-P>P-PRINT)  Upon completion of the MN-CON clear, re-enter the service mode contents listed on the p-print.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E292 - Service Support Tool Error
Error :When attempting to download system software, the laptop displays an E292 code.

Workaround :
The connection to the imageRUNNER was confirmed using the ping command.  In this case, the tech had registered only "English" language into the Service Support Tool.  When additionally registering the "Japanese" language in the Service Support Tool, the imageRUNNER took the download without getting the E292 code.

Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E400-0002 on the Display
Error :The error code E400-0002 is shown on the display when trying to make copies.

Workaround :
The solution in this case was to reseat the Document Feeder-N1 interface cable AND clear RCON.

*Note* The feeder width adjustment must be done after clearing RCON.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570Finisher-Q1 / Q3 Saddle Fnisher Q2 / Q4
Title : E505 Error Code
Problem :E505 is defined as a Backup Ram error.The Finisher Controller had just been replaced in response to a different error code. When attempting to adjust the Alignment Position, the Alignment Plates will not move into position.

Solution :
When replacing the Finisher Controller the following adjustments must be made:
1. Alignment Position
2. Staple Position

It was discovered that the Finisher Front Cover Switch (MS31 ) was not being actuated. Without proper activation of MS31the necessary adjustments cannot be made. After activating the Front Cover Switch The adjustments were performed, and the problem was solved.

Product : imageRUNNER 2230/2830/3530
Title : E508
Error :E508 is displayed on the control panel after installing a Q1 or Q3 finisher.

Workaround :
The only Finisher that the imageRUNNERs 2230/2830/3530 support is the Finisher S-1. This error code of E508 is not found in  the Service Manual but happens when either the Finisher Q1 or Q3 are installed on these "30" series machines. The "30" series machines do not support the Finisher Q1 or Q3.

Product : imageRUNNER 2270 imageRUNNER 2870  imageRUNNER 3570 imageRUNNER 4570 imageRUNNER 2230 imageRUNNER 2830 imageRUNNER 3530
Title : E520 sub code 8001
Error :The pick up roller will move towards the rear and start to vibrate, then the E520 is generated with the sub code 8001.

Workaround :
Replacing the offset motor resolved the E520 - 8001.

M4 Offset Motor
Part number 4K1-4053-000

Product : Finisher-T1 / Saddle Finisher-T2 / Finisher-AD1 / Saddle Finisher-AD2 / Finisher-AE1 / Saddle Finisher-AE2 / Finisher-Q3 / Saddle Finisher-Q4 / Finisher-AA1 / Saddle Finisher-AA2 / Finisher-R1 / Saddle Finisher-R2 / Finisher-Q1 / Saddle Finisher-Q2 / Finisher-Y1 / Saddle Finisher-Y2 / Finisher-N1 / Saddle Finisher-N2 / Finisher-W1 / Saddle Finisher-W2 / Finisher-H1 / Saddle Finisher-H2 / Finisher-AC1 / Saddle Finisher-AC2 / Staple Finisher-C1 / Booklet Finisher-C1 / Staple Finisher-B1 / Booklet Finisher-B1 / Staple Finisher-E1 / Booklet Finisher-E1
Title : E531 with sub code 0001 / 0002
Error : The E531 error code indicates an issue with the stapler motor or stapler home position detection sensor.

In this occurrence of the E531, the stapler will drive to the rear staple position, paper will accumulate in the operation tray and generate the E531 at the time of staple.  Staple assembly, staple harness ribbon cable and the finisher controller were replaced, the finisher continued to error with the E531.

Workaround :
It was found that MSW104, staple safety switch was not properly actuated.  The spring on the white actuator was missing.

This switch cuts 24v to the stapler motor M11 and is actuated when the swing guide is forced in the maximum open position.

A quick way to check MSW104 is from the finisher controller at J714 pins 1 & 2.  Pin 1 should read 24v constant and pin 2 will read 24v when MSW104 is actuated, and 0v when MSW104 is opened.
If pin 1 reads 24v and pin 2 reads 0v whether MSW104 is actuated or open, replace MSW104.
MSW104 part number is FH7-6379-000

Note: Due to the range of Finishers covered in this Knowledge Base article, the safety switch maybe addressed by a different identification number.  Please check the related Service Manuals & Parts Catalog for correct identificationProduct : imageRUNNER 2270 series, S1 Finisher Title : E540Error :
Error code E540. Dealer had replaced the tray harnesses and the finisher controller pcb with no change in symptom.

Workaround :
Solution was to replace the Finisher Controller FG1-1478-060 and the Stack Tray Motor (M1) 4K1-4055-000 as M1 was shorted out and causing the Finisher Controller to fail

Product : imageRUNNER 2270 / 2870 / 3570 / 4570, S1 Finisher
Title : E540 0001
Error :E540 error code with a sub code of 0001 is not listed in the service manual.

Workaround :
If this code is displayed and the bin will not lower:
Check PI 10, tray lower limit sensor operation. If defective replace the sensor.
Part # W68-5571-000

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E540 sub code 8005
Problem : The machine is giving an E540 error code with a sub code of 8005.  This sub code is not listed in the service manual.  The error code corrections are listed in tech pub TP06 238.

The delivery tray will drive all the way to the top and then the error code will be displayed.

Solution :
Check FU3 on the upper left corner of the finisher controller.  If it checks out good, power the machine off and lower the finisher delivery tray by hand and power the machine back on.

If the fuse is blown, replace the finisher controller.
Part number 4G1-1478-050

Product : imageRUNNER 2230 / 2270 / 2870 / 3530 / 3570 / 4570, S1 finisher, B1 tray
Title : E542
Error : An intermittent error code of E542 and sometimes E584 was present.

Workaround :
The solution to remedy both intermittent codes was to replace the B1 harness part number 4G1-2262-000

Product : imageRUNNER 2230 / 2230G / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3530G / 3570 / 4570 
Title : E542 Sub Code 8004.
Error : E542-8004 code occurs when tray B continues to drive down and binds up causing a clicking noise before the code appears.

Workaround :
In this particular case the option tray escape position sensor PI14 was faulty. Replacing PI14 part number WG8-5571-000 resolved the problem.

 Product : imageRunner 2230 / 2230G / 2270 / 2830 / 2870 / 3530 / 3530G / 3570 / 4570 imageRunner C3100 / C3170 Finisher S1
Title : E584 Codes
Problem : If the Optional Bin B1 is installed, various Error Codes may result if the Finishers cover screws are not all installed and fully tightened

Solution :
The covers on the Finisher S1 and P1 are an important part of the Finisher frame, if all the cover screws are not installed and tightened the frame will flex excessively. The most common problem when the optional Tray- B1 is installed is that the shutter will intermittently contact the upper or lower bin resulting in a loud noise and / or E584 Codes.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Finisher Q3 Punch Unit R1
Title : E593-8002
Error : E593-8002

Workaround :
In this case it was found that there was packing material left in the Punch Unit R1 during a new install. Upon the removal of the packing material the Punch Unit was able to move freely and the error code was resolved.

Product : imageRUNNER 3025 / 3030 / 3035 / 3045
Title : E602 - 0105
Problem : The machine is displaying an error code of E602 with a sub code of 0105.  This sub code is not found in the service manual.  Typically, an E602 indicates and error with the hard drive.

Solution :
Replaced the SDRAM on the Main Controller and the issue was resolved.
Part number WA7-4625-000.

 Product : ImageRUNNER 2230/2230G/2270/2830/2870/3530/3025/3030/3035/3045/3530G/3570/4570
Title : E602-0105
Problem : Error code E602-0105, replacement of the Hard Drive,  reloading SSW  and reformatting Hard Drive does not resolve the error code.

Solution :
The Hard Drive was corrupt and was corrupting the main controller and would corrupt any new Hard Drive that was replaced into the machine and if that Hard Drive was tested into another machine it took out that Main Controller also. To resolve this issue the Hard Drive and the Main Controller had to be replaced as a set, format the HDD and load SSW.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570
Title :E610 Error Code
Error : E610

Workaround :
The E610 error code is generally associated to an imageRUNNER equipped with a security kit.  The security kit is LMS activated, but also contains an Expansion Bus Board and a USB Application Interface Board which connects to the main controller.  If the Expansion Bus Board or USB Application Interface Board is removed or has a loose connection to the main controller, an E610 error code may be generated.

Reset and / or reinstall the Expansion Board and the USB Application Interface Board to resolve the E610 code.

Product : imageRUNNER 3030/3035/3045
Title : E611-0000 is on the display
Error : E611-0000 is on the display. The code usually would happen sporadically.

Workaround :
In this case, clearing sectors of the HDD resolved the issue. There have also been some instances where clearing the MNCON has also resolved this error code. A definition of this code is not found in the this product series documentation. Below is a description of the code:

E611-0000
Error in repeat of reboot due to fault of the SRAM, etc.

SRAM information has failed, job information stored in the SRAM cannot be read and a reboot is repeated at recovery from powering off

Product : imageRUNNER  2230/2270/2830/2870/ 3530 /3570/ 4570
Title : E674-0008
Error : Although the error code of E674 is documented in the Service Manual, the sub code of 0008 is not. In this case, the machine was displaying an E674-0008.

The Service Manual describes that an E674 is related to a communication fault between the multi line fax pcb and the Main Controller pcb. When looking in Service Mode>Copier>Display>Version>Fax, the machine displayed, a "??#" for the version of the fax. The machine in this case was flashed. Other symptoms experienced were, no dial tone when using the "On-Hook" key using the fax function, the machine could not print any internal/external prints,  the machine could not complete the "forced shut down procedure" and would "lock up".  Although these symptoms were experienced, the machine was able to copy without problems.

Workaround :
Following the Service Manual's instructions, the multi line fax pcb assembly was disassembled. Upon inspecting the unit, it was noticed that one of the ribbon cables on the G3 fax control pcb was not seated properly. After reseating the ribbon cables on the G3 fax control pcb, the machine stopped displaying this error code. The fax functionality then returned and the machine stopped exhibiting the other symptoms listed above. Checking and reseating the ribbon cables located on the G3 fax control pcb resolved the issue.

Related Service Manual error code information for an E674 code is:
1. sub code 0001- An attempt to set mode for the fax device has failed

Remarks for items to check are:
1. Check the connection of the cable between the fax control PCB (2 line) and the main controller PCB.
2. Replace the ROM DIMM of the fax control PCB (2-line).
3. Check ribbon cables within the fax pcb assembly.
4. Replace the fax control PCB (2 line).
5. Replace the main controller PCB.

Product : imageRUNNER  2270 / 2870 / 3570 / 4570  imageRUNNER 2230 / 2830 / 3530
Title : E716 error code
Error : Error code E716 occurs with the Finisher-S1 is installed. The error code refers to the Cassette Feeding Unit-Y2, which may not be installed. If the Finisher-S1 is disconnected the error code will clear.

Workaround :
If the error code E716 is present upon install of a iR XX30 series machine, make sure a 3-Way Unit-A1 is installed.  See KB article 54256 for further information.

If the error code E716 is generated on a iR XX30 or iR XX70 series unit:

Check to see if the error clears when the Finisher-S1 is removed.  If the error clears, check for 13VA2 and 24VA going to the 3-way unit-A1.  The 13v & 24v is can be checked at J646 of the Accessory Power Supply, pin 1 (13v), pin 3 (24v) to J741 of the 3 way unit-A1, pin 7 (13v), pin 9 (24v).  If the voltage is present, replace the 3 way unit-A1 controller.  PN:  FM2-3221-000. 

Product : iR4570 series
Title : E732
Error : E732-0001 can be displayed when the DDI-S communication error occurs, meaning the communication betwen the Reader and MCON.

Workaround :
  1. Re-insert the connector J1014 ( reader wire harness for DDI communication) on the Main controller PCB.
  2. If the symptom still occurs, pull the memory and DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381).Clean the contacts with a clear rubber erasure and re-insert the DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381).
  3. If the symptom still occurs, replace the Reader Controller PCB with a new one.  FG3-3765-000 = Reader Controller PCB Assemb
Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E733 Error Code After Replacing the Boot Rom
Error : A new boot rom was inserted into a slot and the machine was turned on.  The E733 came up on the display after a few minutes.

Workaround :
In this case, the boot rom was mistakenly placed in the slot located on the DC Controller.  The Boot Rom slot on the Main Controller is the same size as the DCON Dimm slot on the DC Controller.  Hastily replacing this chip without confirming the correct slot will damage the chip.  NOTE: If you are installing a network boot rom and it is damaged, you will need to contact the TSC for the replacement procedure.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Finisher-S1
Title : E733-0001 Error Code
Error : The imageRUNNER is displaying an error code of E733-0001. The code is consistent, and will occur when an attempting to make a copy. After the start key is pressed, the paper will feed to the registration roller, and the imageRUNNER will go into code.

Workaround :
An E733-0001 indicates a communication problem, usually between the DC and Main Controller. In this example the problem was rectified by replacement of the Finisher Controller. A possible scenario, would be to disconnect the finisher to observe a change in symptom. If the imageRUNNER will output paper, or at least feed paper past the previous point, the problem may lie in the finisher.

S1-Finisher Controller P/N - 4G1-1478-060

Product : imageRUNNER 2230 / 2830 / 3530 / 4530
Title : E744-1000
Problem : While flashing machine, power in office shut off while writing to Boot-rom. After rebooting machine, could not write software to Boot-rom.

Solution :
Boot-rom software was damaged during power failure. Part number for Boot-rom is FM2-3803-600.Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E749Error :
E749 in Error History.

Workaround :
An E749 is in the error history after installing / uninstalling a Printer Kit or MEAP device in the iR2270, 2870, 3570, 4570. This error only occurs once when this type of installation has been done.This error may only be displayed in history and not on the LCD Display.Cycle the power of the machine after installation of these options.

Product : imageRUNNER 2230 / 2270 /2830 / 2870 / 3530 / 3025 / 3030 / 3035 / 3045 / 3570 / 4570 / 3225 / 3230 / 3235 / 3245
Title : E805
Error : E805

Workaround :
It has been found that the exhaust fan can become dirty or locked up.  Clean the fan and make sure the fan blades spin freely.  In some cases the fan needs to be replaced.  Fan part number is (FK2-0360-000) for both fans.

Labels: canon imagerunner error codes IR 3035 * 3045 * 3530 * 3530G * 3570 * 4570 2525 * 2530 * 2535 * 2535i * 2545 * 2545i canon copier
canon error codes e602 e540 e001 e000 e732 copiers copy machine
canon imagerunner error codes IR 3035 * 3045 * 3530 Canon Copie

Error Code in Canon iR5000/iR6000

These are all list of Error Code in Canon iR5000/iR6000 more to come, i hope your machines works fine and never get error.
*E001

Main cause: The main thermistor (TH1) has a short circuit.The sub thermistor (TH2) has detected overheating.The SSR is faulty.The DC controller PCB is faulty.Mode of detection:0001 The main thermistor or the sub thermistor has detected about 230ºC or higher for 2 sec.0002 The main thermistor has detected 230ºC or higher (hard circuit detection)0003 The sub thermistor has detected about 236ºC or higher. Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E002

Main cause: The main thermistor (TH1) has poor contact or an open circuit.The thermal switch (TP1) has an open circuit.The SSR is faulty.The DC controller PCB is faulty.Mode of detection:0000 The temperature of the upper fixing roller does not reach 100ºC within 2 min after it has exceeded 70ºC. Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E003

Main cause: The main thermistor (TH1) has poor contact or an open circuit.The thermal switch (TP1) has an open circuit.The fixing heater has an open circuit.The SSR is faulty.The DC controller PCB is faulty.Mode of detection:0000 The temperature detected by the main thermistor is 70ºC for 2 sec or more after it has reaced 100ºC. Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E004

Main cause: The SSR has a short circuit. The DC controller PCB is faulty.Mode of detection:0000 The SSR used to drive the fixing heater is found to have a short circuit (hard circuit detection). Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E005

Main cause: The fixing web has been taken up. The fixing web length sensor (PS45) is faulty.The DC controller PCB is faulty.Mode of detection:0000 The length of fixing web that has been taken up is in excess of the specified length. Caution: After replacing the fixing web, be sure to reset the two web counters in service mode:COPIER>COUNTER>MISC>FIX-WEB and COPIER>COUNTER>DRBL-1>FX-WEB.

*E010

Main cause: The main motor (M2) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The clock pulse do not arrive for 2 secs or more after the main motor drive signal (MMFG) has been generated.

*E012

Main cause: The drum motor (M1) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The clock pulses do not arrive for 2 secs or more after the drum motor drive signal (DMFG) has been generated.

*E013

Main cause: The waste toner feedscrew is faulty. The waste toner clock sensor (MSW2) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The rotation of the waste toner feedscrew goes out of order, and the switch (MSW2) is pressed multiple times during a specific period of time.

*E014

Main cause: The fixing motor (M19) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The motor clock signal is detected for 2 secs or more continuosly after the fixing motor drive has been generated.

*E020

Main cause: The hopper connector is left disconnected. The hopper motor (M9/M10) is faulty.The toner sensor (TS1/TS2) is faulty. The DC controller PCB is faulty.Mode of detection:0000 During printing, the toner supply is '0' (absence of toner) for 2 mins.

* E032

Main cause: The copy data controller or the remote diagnostic device is faulty. The main controller PCB is faulty.Mode of detection:0001 Although once connected,the copy data controlleror the remote diagnostic device has become disconnected.

* E061

Main cause: The laser shutter is faulty. The laser unit is faulty. The potential measurement PCB is faulty. The DC controller PCB is faulty.Mode of detection:0001 As the result of potential control,the drum surface potential (VL2) of the white background is about 200V
(generating solid black images).0002 The primary charging output used for print output and the drum surface potential after laser output has been made are about 200V (generating solid black images).

* E100

Main Cause: The BD PCB is faulty. The laser unit is faulty. The laser driver PCB isfaulty. The wiring is faulty (short circuit, open circuit). The DC controllerPCB is faulty.Mode of Detection:0001 In 100 msec after the laser drive signal has been generated, the BD signal is not detected 50 times or more
within 40 msecs.0002 While the laser is on, the BD signal cycle is found to be outside aspecific range 10 times or more.

* E110

Main Cause: The laser scanner motor (M15) is faulty. The wiring is faulty (short circuit,open circuit). The DC controller PCB is faulty.Mode of Detection:0001 • After the laser scanner motor drive signal has been generated,the motor ready signal (LMRDY*) does not arrive for
15 secs or more. (stop - full speed, half-speed - full speed)• During the period of 'full speed - half speed', the motor ready signal does not arrive for 60 secs or more after
the speed change signal has been generated.• During the period of 'full speed rotation', the motor ready signal is not detected 50 times or more (t intervals of 100 msec).

* E121

Main Cause: The controller cooling fan (FM4) is faulty. The wiring is faulty (short circuit,open circuit). The DC controller PCB is faulty.Mode of Detection0001 Although the controller cooling fan (FM4) is being driven, the clock signal (FM4LCK) does not arrive for 5 secs or more.
E196Main Cause: The EEPROM on the DC controller PCB is faulty. The location of the EEPROM is wrong. The DC controller PCB is faulty.Mode of Detection:1abb When data is written to the EEPROM, the data written and the data read do not match.2abb When the ID read into the EEPROM and the ID into the ROM are compared, a mismatch is found.3abb When ID in the EEPROM and the ID in the ROM are compared after the main power switch is turned on, a mismatch is found.a: chip Nos. 0 through 5 (0: IC104, 1: IC105, 2: IC109, 3: IC110, 4: IC127, 5: IC130)bb: chip faulty address (bit)

* E202

Main Cause: The scanner HP sensor (PS39) is faulty. The scanner motor (M3) is faulty. The reader controller PCB is faulty.Mode of Detection:0001 The scanner HP sensor does not turn off even when the scanner has been moved 40 mm forward after the main power switch has been turned on or the Start key has been pressed.0002 The scanner HP sensor does not turn on even when the scanner has been moved 450 mm in reverse.Caution No code is indicated, and keys are locked. The code may be checked in service mode (COPIER>DISPLAY>ERR).

* E204

Main Cause: The ADF controller PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0001 During printing, the image leading edge signal does not arrive from the ADF.Caution No code is indicated, and keys are locked. The code may be checked in service mode (COPIER>DISPLAY>ERR).

* E220

Main Cause: The lamp inverter PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0001 The lamp inverter PCB is found to have a fault.

* E225

Main Cause: The scanning lamp (xenon tube) is faulty. The inverter PCB is faulty. The CCD/AP PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0000 A specific signal level cannot be attained by CCD gain correction at power-on.0002 The edge gain correction value changed more than a specific level compared with the correction value used for the preceding sheet.

* E240

Main Cause: The main controller PCB. The DC controller PCB is faulty.Mode of Detection:0000 An error has occurred in the communication between the main controller PCB and the CPU of the DC controller PCB.

* E243

Main Cause: The control panel CPU PCB is faulty. The main controller PCB is faulty.Mode of Detection:0000 An error has occurred in communication between the CPU of the control panel CPU PCB and the main controller PCB.

* E248

Main Cause: The EEPROM on the reader controller PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0001 The ID read into the EEPROM when the main power switch has been turned on and the ID in the ROM do not match.0002 When data is written into EEPROM, the data written and the data read do not match.0003 When data is written, the ID in the EEPROM and the ID in the ROM are found not to match.

* E302

Main Cause: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty.Mode of Detection:0001 During shading, the reader controller PCB does not end shading in 1 sec.0002 In stream reading, the edge white accumulation (processing) does not end after a period of 10 secs.

* E601

Main Cause: The wiring is faulty (short circuit, open circuit). The hard disk drive is faulty. The DC controller PCB is faulty. The main controller PCB is faulty.Mode of Detection:0000 The main controller PCB has detected an error in control datawhile an image was transmitted between the main controller PCBand the hard disk drive.0001 The main controller PCB has found an error in the control data intransfer of images between main controller PCB and the DC controllerPCB.

* E602

Main Cause The wiring is faulty (short circuit, open circuit). The hard disk drive isfaulty. The main controller PCB is faulty.Mode ofDetection0001 A mount error was detected when the hard disk was started upfrom the boot ROM.0002 A data read error (from the hard disk) was detected when the harddisk was started from the boot ROM.

* E607

Main Cause The hard disk fan (FM7) is faulty. The wiring is faulty (short circuit, opencircuit). The DC controller PCB is faulty.Mode ofDetection0000 While the hard disk fan (FM7) is being driven, the clock signal(FM7CLK) does not arrive for 5 secs or more.

* E677

Main Cause The various printer board (accessories) are faulty. The main controller PCB is faulty.Mode ofDetection0001 An error has occurred in the communication between the various

* E710

Main Cause The DC controller PCB is faulty. The reader controller PCB is faulty.The main controller PCB is faulty.Mode ofDetection0001 When the main power is turned on, the IPC (IC5021) on the readercontroller PCB cannot be initialized.0002 When the main power is turned on, the IPC (IC120) on the DCcontroller PCB cannot be initialized.0003 When the main power is turned on, the IPC (IC1003) on the maincontroller PCB cannot be initialized.

* E711

Main Cause The connector is not connected properly. The remote diagnostic device PCBis faulty. The copy data controller PCB is faulty. The ADF controller PCB isfaulty. The ADF controller PCB is faulty. The finisher controller PCB isfaulty.Mode of Detection 0001 Data has been written to the error register of the IPC (IC5021) onthe reader controller PCB four times or more within 1.5 secs.0002 Data has been written to the error register of the IPC (IC120) onthe DC controller PCB four times or more within 2 secs.0003 Data has been written to the error register of the IPC (IC1003) ofthe main controller PCB four times or more within 2 secs.

* E712

Main Cause The connector is not connected properly. The ADF 24-V power supply isfaulty. The ADF controller PCB is faulty. The reader controller PCB isfaulty.Mode ofDetection0001 Communication does not resume in 3 secs after data has been writtento the error register of the communication IC (IPC) of the ADFcontroller PCB.0002 The transmission bit is not enabled after a period of 10 sec at thesync register of the IPC (IC5021) on the reader controller PCB.

* E713

Main Cause The connector is not connected properly. The finisher accessories powersupply PCB is faulty. The finisher controller PCB is faulty. The DC controllerPCB is faulty.Mode ofDetection0000 The communications IC (IPC) on the finisher controller has goneout of order.

* E717

Main Cause The wiring is faulty (short circuit, open circuit). The copy data controller orthe remote diagnostic device is faulty. The main controller PCB is faulty.Mode ofDetection0001 The copy data controller or the NE controller is out of order or anopen circuit has been detected.Caution The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR).

* E719

Main Cause The wiring is faulty (short circuit, open circuit). The coin vendor is faulty.The main controller PCB is faulty.Mode of Detection0001 The communication between the coin vendor and the main controllerPCB has been interrupted.Caution The error must be reset in service mode (COPIER>FUNCTION>CLEAR>ERR).

* E732

Main cause The connector has poor contact. The reader controller PCB is faulty.Mode ofDetection0001 The main controller PCB has detected an error in the communicationbetween the reader controller PCB and the main controllerPCB.

* E733

Main cause The connector has poor contact. The DC controller PCB is faulty.Mode ofDetection0001 The main controller PCB has detected an error in the communicationbetween the DC controller PCB and the main controller PCB.CLEAR>ERR).printer boards (accessories) and the main controller PCB.

* E740

Main cause The LAN card is faulty. The main controller PCB is faulty.Mode ofDetection0001 An error is detected on the LAN card at power-on (with the cardinserted).0002 A MAC address is found to be faulty.0003 The LAN card register cannot be read.

* E741

Main Cause The PCI bus connection is not proper. The main controller PCB is faulty.Mode ofDetection0000 An error has occurred in the PCI bus.

* E742

Main Cause The RIP1 board (accessory) is faulty. The main controller PCB is faulty.Mode ofDetection0000 An error has been detected by self diagnosis of the RIPI board.

* E743

Main cause The connector has poor contact. The main controller PCB is faulty.Mode of Detection 0000 The reader controller PCB has detected an error in the communicationbetween the main controller PCB and the reader controllerPCB.

* E804

Main Cause The wiring is faulty (short circuit, open circuit). The DC power supply fan(FM6) is faulty. The DC controller PCB is faulty.Mode ofDetection0000 While the DC power supply fan is being driven, the clock signal(FM6CLK) does not arrive for 5 secs or more.

* E805

Main Cause The wiring is faulty (short circuit, open circuit). The feed fan (FM1) isfaulty. The heat discharge fan (FM3) is faulty. The DC controller PCB isfaulty.Mode ofDetection0001 While the heat discharge fan is being driven, the clock signal(FM3CLK) does not arrive for 5 secs or more.0002 While the feed fan is being driven, the clock signal (FM1CLK)does not arrive for 5 secs or more.

* E824

Main Cause The wiring is faulty (short circuit, open circuit). The primary charging assemblycooling fan (FM2) is faulty. The DC controller PCB is faulty.Mode ofDetection0000 While the primary charging assembly cooling fan is being driven,

* E412

Main Cause The cooling fan (FM1) is faulty. The ADF controller PCB is faulty.Mode ofDetection0001 While the cooling fan is being driven, the lock signal (FMLCK)arrives for 100 msec or more.

* E420

Main Cause The EEPROM is faulty. The ADF controller PCB is faulty.Mode of Detection 0001 When the host machine's power switch is turned on, the backupdata of the EEPROM cannot be read or the data, if read, has an error.

* E421

Main Cause The EEPROM is faulty. The ADF controller PCB is faulty.Mode ofDetection0001 Backup data cannot be written to the EEPROM or the data, if written,has an error.the clock signal (FM2CLK) does not arrive for 5 secs or more.

* E422

Main Cause The IPC communication has an error. The communication line has an opencircuit. The ADF controller PCB is faulty.Mode ofDetection0001 While the machine is in standby, the communication with the hostmachine has been interrupted for 5 secs or more. or, while the machineis in operation, the communication with the host machine hasbeen interrupted for 0.5 sec or more.

* E500

Main Cause The finisher controller PCB is faulty. The DC controller PCB is faulty.Mode ofDetection0001 The communication between the host machine and the finisher hasbeen interrupted; this error is detected by the host machine.

* E503

Main Cause The saddle stitcher controller PCB is faulty. The finisher controller PCB isfaulty.Mode ofDetection0002 The communication between the saddle stitcher controller PCBand the finisher controller PCB has been interrupted.

* E504

Main Cause The height sensor (PS1) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 Communication between the height sensor and the finisher controllerPCB is not possible, or communication data has an error.0002 Communication between the height sensor and the finisher controllerPCB is not possible for a specific period of time.0003 At time of power-on, the connector of the height sensor is found tobe disconnected.0004 When the height sensor is being adjusted using the DIP switch, anerror occurred during the adjustment.

* E505

Main Cause The EEPROM is faulty. The finisher controller PCB is faulty. The puncherdriver PCB is faulty.Mode ofDetection0001 When the power switch is turned on, the check sum of theEEPROM on the finisher controller PCB is found to have an error.0002 When the power switch is turned on, the check sum of theEEPROM on the puncher driver PCB is found to have an error.

* E512

Main Cause The delivery motor clock sensor (PI10) is faulty. The delivery motor (M2)is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 When operation starts, as many clocks as needed do not arrivefrom the delivery motor clock sensor.0002 No clock pulse arrives while paper is being moved over a distanceof 200 mm.

* E530

Main Cause The alignment plate home position sensor (PI6) is faulty. The alignmentmotor (M3) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The alignment plate does not leave home position when the alignmentmotor has been driven for 2 secs.0002 The alignment plate does not return to home position when thealignment motor has been driven for 2 secs.

* E531

Main Cause The stapler home position detecting switch (MS7) is faulty. The stapler motor(M6) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The stapler does not leave home position when the stapler motorhas been driven for 0.5 sec.0002 The stapler does not return to home position when the stapler motorhas been driven for 0.5 sec.

* E532

Main Cause The stapler shift home position sensor (PI7) is faulty. The stapler shift motor(M4) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The stapler unit does not leave home position when the stapler shiftmotor has been driven for 4 secs.0002 The stapler unit does not return to home position when the staplershift motor has been driven for 4 secs.

* E535

Main Cause The swing motor clock sensor (PI20) is faulty. The swing guide open sensor(PI18) is faulty. The safety area switch (MS3) is faulty. The swing guideclosed detecting switch 2 (MS6) is faulty. The swing motor (M7) is faulty.The finisher controller PCB is faulty.Mode ofDetection0001 The swing guide closed detecting switch 2 does not turn on whenthe swing motor has been rotated CCW for 1 sec.0002 The swing guide open sensor does not turn on when the swing motorhas been rotated CW for 1 sec.0003 When the tray lift motor is in operation, the swing guide closed detectingswitch 2 is found to be off while the tray 1/2 is at OFF positionof the safety area switch.0004 No clock arrives for 200 msecs while the machine is in swing operation.

* E540

Main Cause The tray home position sensor (PI8) is faulty. The tray lifter motor clocksensor 1/2 (PI9/PI19) is faulty. The tray upper limit detecting switch (MS5)is faulty. The tray lifter motor (M5) is faulty. The finisher controller PCB isfaulty.0001 The ascent does not end in 15 secs when the tray lift motor isdriven; or, the tray home position cannot be detected when the traylift motor has been driven for 15 secs.0002 While the tray is moving up, the tray upper limit detection switchis found to be on.0003 When the tray lift motor is driven, clock pulses do not arrive fromthe clock sensor 1/2 for 200 msecs.

* E584

Main Cause The shutter open sensor (PI5) is faulty. The safety area detecting switch(MS3) is faulty. The shutter closed detecting switch (MS4) is faulty. TheNo. 2 feed motor (M8) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The shutter closed detecting switch does not turn on when the No.2 feed motor has been rotated CCW for 1 sec or more.0002 The shutter open sensor does not turn on when the No. 2 feed motorhas been rotated CCW for 1 sec.0003 While the tray lift motor is in operation, the shutter closed detectingswitch is found to be off when the tray 1/2 is at OFF positionof the safety area detecting switch.

* E590

Main Cause The punch home position sensor (PI3P) is faulty. The punch motor (M1P)is faulty. The punch driver PCB is faulty.Mode ofDetection0001 The puncher does not leave home position when the punch motorhas been driven for 200 msecs.0002 The puncher does not return to home position when the punch motorhas been driven for 200 msecs.

* E593

Main Cause The horizontal registration home position sensor (PI1P) is faulty. The horizontalregistration motor (M1P) is faulty. The punch driver PCB is faulty.Mode ofDetection0001 The puncher does not leave home position when the horizontal registrationmotor has been driven for 4 secs.0002 The puncher does not return to home position when the horizontalregistration motor has been driven for 4 secs.

* E5F0

Main Cause The paper positioning plate home position sensor (PI7S) is faulty. The paperpositioning plate motor (M4S) is faulty. The saddle stitcher controllerPCB is faulty.Mode ofDetection0001 The paper positioning plate home position sensor does not turn onwhen the paper positioning plate motor has been driven for about1.3 secs.0002 The paper positioning plate home position sensor does not turn off1 sec after the paper positioning plate motor has been driven for 1sec.

* E5F1

Main Cause The folding motor clock sensor (PI4S) is faulty. The paper folding homeposition sensor (PI21S) is faulty. The folding motor (M2S) is faulty. Thesaddle stitcher controller PCB is faulty.Mode ofDetection0001 The number of detection pulses of the folding motor clock sensordrops below a specific value.0002 The state of the paper folding home position sensor does notchange when the folding motor has been driven for 3 secs.

* E5F2

Main Cause The guide home position sensor (PI13S) is faulty. The guide motor (M3S)is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The guide home position sensor does not turn on when the guidemotor has been driven for about 0.5 sec.0002 The guide home position sensor does not turn off when the guidemotor has been driven for 1 sec.

* E5F3

Main Cause The alignment home position sensor (PI5S) is faulty. The alignment motor(M5S) is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The alignment plate home position sensor does not turn on whenthe alignment motor has been driven for 0.5 sec (initially, drivenfor about 1.7 sec).0002 The alignment plate home position sensor does not turn off whenthe alignment motor has been driven for 1 sec.

* E5F4

Main Cause The stitch home position sensor (rear, MS5S) is faulty. The stitch motor(rear, M6S) is faulty. The saddle stitcher controller PCB is faulty.Mode of Detection 0001 The stitcher home position sensor (rear) does not turn off when thestitch motor (rear) has been rotated CW for 0.5 sec or more.0002 The stitch home position sensor (rear) does not turn on when thestitch motor (rear) has been rotated CCW for 0.5 sec or more.

* E5F5

Main Cause The stitch home position senor (front, MS7S) is faulty. The stitch motor(front, M7S) is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The stitch home position sensor (front) does not turn off when thestitch motor (front) has been rotated CW for 0.5 sec or more.0002 The stitch home position sensor (front) does not turn on when thestitch motor (front) has been rotated CCW for 0.5 sec or more.

* E5F6

Main Cause The paper push-on plate motor clock sensor (PI1S) is faulty. The paperpush-on plate leading edge position sensor (PI15S) is faulty. The paperpush-on plate home position sensor (PI14S) is faulty. The paper push-onplate motor (M8S) is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The paper push-on plate home position sensor does not turn onwhen the paper push-on plate motor has been driven for 0.3 sec ormore.0002 The paper push-on plate home position sensor does not turn offwhen the paper push-on plate motor has been driven for 0.3 sec ormore.0003 The paper push-on plate leading edge position sensor does not turnoff when the paper push-on plate motor has been driven for 0.3 secor more.0004 The number of detection pulses of the paper push-on plate motorclock sensor drops below a specific value.0005 The paper push-on plate leading edge sensor does not turn onwhen the paper push-on plate motor has been driven for 0.3 sec or more.

* E5F8

Main Cause The guide home position sensor (PI13S) is faulty. The paper push-on platehome position sensor (PI14S) is faulty. The paper push-on plate leadingedge position sensor (PI15S) is faulty. The saddle stitcher controller PCB isfaulty.Mode ofDetection0001 The connector of the guide home position sensor is found to bedisconnected.0002 The connector of the paper home positioning plate home positionsensor is found to be disconnected.0003 The connector of the paper push-on plate leading edge positionsensor is found to be discontented.

* E5F9

Main Cause The inlet door switch (MS1S) is faulty. The front door switch (MS2S) isfaulty. The delivery door switch (MS3S) is faulty. The saddle stitch controllerPCB is faulty.Mode of Detection 0001 When the inlet cover, front cover, and the delivery cover are foundto be closed, the inlet door switch detects an open condition for 1sec or more from the start of the initial rotation of the host machineor the start of printing.0002 When the inlet cover, front cover, and delivery cover are found tobe closed, the front door switch detects an open condition for 1 secor more after the start of the initial rotation of the host machine orthe start of printing.0003 When the inlet cover, front cover, and delivery cover are found tobe closed, the delivery door switch detects an open condition for 1sec or more from the start of the initial rotation of the host machineor the start of printing.

Incorrect Paper Size and Stop Printing Canon Ir1600 & Ir2000

Cara Mengatasi Incorrect Paper Size Canon Ir1600 dan Ir2000.

1. Tekan Additional Functions (*)
2. Tekan ID (#) keluar SERVICE MODE
3.  Tekan panah kekanan (>) cari #7 PRINTER tekan OK
4. Tekan panah kekanan (>) cari #6 CST tekan OK
5. Tekan panah kekanan (>) cari  CST U2 jika posisi angka Nol (0) ganti menjadi 24  tekan OK
6.  Tekan Reset matikan power dan hidupkan kembali
7. Selesai

Sekarang geser slider size ke U2 untuk pakai kertas Folio

Cara Fotocopy Dari USB Drive Flashdisk.



English: USB flash drive Deutsch: USB-Speicher...

Cara Fotocopy Dari USB Drive Flashdisk di Mesin Fotocopy Canon Imagerunner (Canon iR) seperti Canon ir3245, ir3235, dan 3245i, ir3235i Series baca caranya dibwah ini:

Mencetak dari USB Flashdisk di Canon IR

  • Masukkan Flasdisk anda ke port USB yang berada disebelah kiri layar tuoch screen.
  • Pilih Mail Box USB dan tekan Memory Media.
  • Pilih perangkat Anda dan tekan open.
  • Pilih file yang ingin di cetak menggunakan tombol navigasi di layar dan tekan Start Print.
  • Pilih apakah ingin mencetak semua halaman atau halaman tertentu saja di "Print Range section"
  • Tambahan, Anda dapat mencetak secara bolak-balik (double-sided ) menggunakan tombol 2-Sided Printing.
  • Pilih Start Print.
CATATAN: Mesin Fotocopy Canon ir ini tidak mendukung file dokumen dari Microsoft Office . Canon Image Runner ini hanya mendukung file berformat PDF, TIFF, JPG. Jadi jika file yang ingin dicetak tidak tampil/keluar berarti Fotocopy iR ini tidak mendukung/tdk support dgn file anda..

Error E100 Canon iR | Cara Mengatasi Eror E100 iR1600

Error E100 Canon iR1600 Disini saya kembali membagikan pengalaman saya tentang “Bagaimana Cara Mengatasi Eror E100 iR1600”. Pada awalnya mesin tidak masalah, hanya waktu itu saya ingin membersihkan tumpahan toner yang ada di Magnet roll Devloping dan juga roll transfer akhirnya saya buka semua unit Drum dan Unit Devloping dikeluarin seterusnya semprot pakai kompresor dan dipasang kembali dan coba langsung test print copy tiba2 dilayar langsung keluar error E100. Saya tahu permasalahan ada pada unit lasernya tetapi saya cek lasernya tidak ada masalah, makanya saya gogling di google dan menemukan artikel disitus rusia yang saya translate otomatis ke bahasa indo makanya kata-katanya pada nggak karuan.
E100 - Setelah sinar laser dihidupkan, sinyal BD tidak dapat dideteksi dalam jangka waktu tertentu dan itulah alasan terjadinya kesalahan.
Oke walaupun kata-katanya gak karuan tapi intinya Anda hanya perlu membersihkan kaca kaca pada bagian dalam unit laser itu, dan bagaimana caranya? Ikuti saja petunjuk dibawah ini karena sudah disertai gambar panduannya
Masalah: dengan kerugian minimal antara pusat layanan personel untuk sampai ke unit laser.
Tools: baik, itu rasanya ... Aku dengan Anda di seperti pertempuran akan mengambil: vacuum cleaner untuk mengumpulkan toner, pin obeng kecil, angka (silang) obeng.
Urutan pelaksanaan:
1) Hal pertama yang perlu Anda ekstrak dari kompor aparat.
E100 Kesalahan dalam mesin fotokopi Canon IR1600 
Bagaimana melakukannya? Berikut adalah cara.
Lepaskan penutup kiri
Buka penutup depan
Ekstrak unit drum (drum-.nit)
Lepaskan baki feed manual dan meninggalkan menutupi di sebelah kiri
Lepaskan penutup yang tepat
Lepaskan tutupnya, yang keluar dari mesin kertas
Hapus dari rak kotak transparan. Dia duduk di perekat dan angka adalah sebagaimana diuraikan oleh garis tebal di sepanjang kontur.
Semua mencakup untuk menahan ke hard drive dan removable mudah; penting - akurasi.



Alasan untuk perangkat fotokopi E100 kesalahan dalam Canon IR1600 Ini adalah kotak transparan, hanya gambar yang lebih besar. Angka 2 dan 3 ditandai lubang sekrup. Adalah penting untuk mengingat bagaimana ada kotak yang jelas, jika perakitan, Anda bisa mendapatkan diri dalam teka-teki :-) sedikit menyenangkan







E100 Kesalahan dalam mesin fotokopi Canon IR1600
Lepaskan sekrup (5), kemudian lepaskan tanah (6) dan lepaskan perakitan papan. Fee seakan rak di reses khusus.
Hati-hati dengan itu karena kabel (tampaknya di desainer khusus dikandung perusahaan Canon) tidak memiliki saham untuk panjang.





Untuk memperbaiki kesalahan ini di E100 mesin fotokopi Canon IR1600 Lepaskan 3 x dari perakitan papan (9). Saya harus mengatakan bahwa konektor putih besar setelah Anda melepas konektor yang lebih nyaman untuk masuk ke dalam (relatif terhadap papan) bahwa dia tidak berbicara dan tidak mengganggu Anda dalam usaha masa depan.
Semua kabel yang dibutuhkan untuk menarik keluar dari pemotongan sisi pada kartu, jika tidak, anda tidak akan dapat menghapus kompor.







E100 Kesalahan dalam mesin fotokopi Canon IR1600E100 Kesalahan dalam mesin fotokopi Canon IR1600Lepaskan 2 sekrup kecil (10) dan 2 sekrup besar panjang (11). Terakhir mudah untuk membuka tutup, jika Anda menyisipkan sebuah tuas kecil di lubang (13) di sekrup A (lihat Gambar Kanan.).
Setelah semua prosedur di atas, menghapus gerakan, kompor halus pada dirinya sendiri. Jika Anda melakukan semuanya dengan benar, Anda akan berhasil. Dewan perakitan dapat mengganggu proses sedikit, tapi saya pikir dengan cara perusahaan menempatkan, Anda akan mengerti tanpa aku.

2) Sekarang laser blok.
Anda dapat menghapus seluruh blok laser seluruhnya. Saya belum pernah menggunakan cara ini, karena sebelum tirai dapat dicapai hanya dengan menghapus penutup atas laser. Tetapi jika Anda ingin, misalnya, pencegahan unit laser, kemudian, tentu saja, harus menghapus itu sepenuhnya.
E100 Kesalahan dalam mesin fotokopi Canon IR1600 Sangat sederhana. Kami mengambil kain lap (1) - adalah bagian dari bahan berpori, segera akan melihat, lepaskan 3 x (2). Memulas 4 sekrup (3) dan lepaskan penutup unit laser (4). Yang terakhir adalah terpasang ke beberapa kait, tidak rusak sebagian dari mereka ...
Sekarang jika Anda melihat unit laser, lalu ke kanan sebelum itu (sambil bergerak sinar) Anda akan melihat tirai sedikit. Anda dapat melakukan percobaan untuk konfirmasi: meninggalkan segala sesuatu di formulir ini, keluarkan tabung dari cartridge dan masukkan sepenuhnya oleh semua aturan kembali. Kami mengambil rana sepenuhnya dan melupakannya ...
Puting mesin - semuanya sudah siap. Terima kasih atas perhatian Anda.

Cara Setting ulang ADF Feeder Fotocopy iR

Cara Setting ulang ADF Feeder Fotocopy Canon iR6570/5570


Mungkin ADF/Feeder Canon iR5570 atau Canon iR6570 anda pernah mengalami ukuran kertasnya tidak sesuai, terpotong, bagian atas turun dll sebaiknya anda lakukanseperti dibawah ini.

"Cara Setting ulang ADF Feeder Fotocopy iR" dan iR 6570 sbb:

Masuk ke Mode Service ( Tekan *28* )
Pilih "FEEDER"
Tekan "TRY-A4" geser posisi penjepit Adf ke

ERROR E 2557 BIZHUB 250 / 350

Penyebab Munculnya kode error E2557 ini terjadi mungkin diantaranya karena:
    • Tinta dan developer tidak seimbang
    • Tinta atau toner berlebihan
    • Ada peringatan isi tinta tetapi mesin tetap dijalankan/dipakai terus
Berikut ini cara mengatasi ERROR E 2557 pada Mesin KONICAMINOLTA BIZHUB 250 / 350
    • tekan PROGRAM ( ada disebelah kanan bawah touchscreen )
    • tekan CHECK DETAIL ( ada kolom bawah touchscreen )
    • tekan Stop pada samping kanan diatas tombol Start
    • tekan 00
    • tekan Stop lagi
    • tekan 01
    • masukkan pasword 00000000
    • tekan LEVEL HISTORY ( lihat perbandingan antara ATDC SET dan ATDC LEVEL /pada intinya posisi ATDC level minimal harus 4.5% dan max 5.5 % jika kurang dari 4,5% maka cenderung akan keluar code error namun jika berlebihan 6,5% keatas maka juga bisa menyebabkan code error namun bila tidak keluar code error bisa dipastikan tinta boros/hasil di kertas kusam
    • tekan END
    • tekan TECH REP CHOICE
    • tekan PRINTER
    • tekan ATDC SENSOR GAIN ( lihat current isinya berapa misalkan posisi 150 naikkan /turunkan caranya dengan tekan C yang ada di bawah angka 0 kemudian tekan angka yang diinginkan secara manual kemudian setelah diisi tekan END agar angka yang dimasukkan tadi tersimpan tekan END sampai EXIT setelah itu cobalah 1 lembar , setelah cek lagi ATDC LEVEL seperti langkah diatas cobalah beberapa kali sampai ATDC LEVEL benar benar normal.
Demikian cara mengatasi ERROR E 2557 pada Mesin KONICAMINOLTA BIZHUB 250 / 350

SEJARAH MESIN FOTO COPY

Mesin Foto Copy

Mesin foto copy merupakan salah satu perangkat electronik yang berfungsi mendupikasikan dokumen.Ide dasar foto copy adalah bayangan,dimana kita ketahui jika kita terkena cahaya maka kita mempunyai bayangan.Bayangan ini yang nantinya ditransfer kesebuah media dan selanjutnya diReproduksi sebagai hasil yang kita lihat sehari-hari.





Penemu Mesin Foto Copy

Mesin Foto Copy pertamakali ditemukan oleh CHESTER F CARLSON. Asal negeri Paman Sam,Amerika Serikat. Chester F Carlson lahir 18 februari 1906 dikawasan kumuh kota seattle,Washigton.semenjak kecil dia harus ikut membantu orangtuanya mendapatkan uang.untuk membiayai pengobatan ayahnya yang mengidam penyakit Tuberculosis.Saat berusia 17 tahun ia harus menelan pil pahit,ibunya meninggal dan selang empat tahun ayahnya juga meninggal,walaupun masa kecilnya hidup penuh tantangan carlson mampu menyelesaikan carir intelektualnya hingga menyelesaikan bangku kuliahnya.Setelah lulus dari Calivornia Insitute of Tecknology,carlson bekerja disebuah perusahaan analisis paten untuk membuat produk electronik.Tugas nya pada saat itu menyalin semua dokumen dengan gambar paten kebeberapa dokumen.Dalam melakukan pekerjaanya Carlson merasa jenuh dan bosan, untuk menulis hal yang sama dan berulang-ulang untuk didokumentasikan temuan orang lain.karena kelelahan kemudian carlson berpikir,bagaimana ia bisa menggandakan dokumen dengan cepat dan praktis.Iapun membaca beberapa referensi tentang mesin cetak.dan akhirnya dia menemukan konsep Electrofotografi yang sekarang kita kenal foto copy.
Pada tahun 1938,dia membuat eksperimen kecil yang memanfatkan bubuk jelaga (karbon) dan penyinaran cahaya dan memindahkan suaatu tulisan dari suatu medium kemedium lainya.ia juga menggunakan konsep poto conduktivity,sebuah proses perubahan electron,jika terkena cahaya .dengan intinya dengan bayangan gambar dapat diproses menjadi suatu image.Gambar bisa digandakan dengan proses perubahan electron tersebut sebagian besar literatur menyebutkan,temuan carlson menciptakan proses mengcopi dengan menggunakan energi electro statik,yaitu xenograpy.Kemudian pada tahun 1942 teknik ini dipatenkan,selama beberapa tahun ia berusaha menyempurnakan temuannya itu.Meski sanagat berguna ,mesin electrofotografi ini tidak diminati banyak orang,karena mesin ciptaanya tidak menjanjikan masa depan bagi kehidupan orang.carlson yang berhasil membuat alat ini harus berjualan konsep bertahun-tahun lamaya agar mesin foto copy itu dapat dijual dipasaran,berbagai perusahaan besar seperti kodak yang menjual peralatan proses pemotretan.IBM dan general Electrik,menolak temuan itu.

Setelah hampir putus asa,charlson mendapat mitra pertama Batelle Memorial Insitute yang bersedia memodali dengan dana dan usaha dan bersama-sama meyakinkan Haloid,sebuah perusahaan menegah Haloid Corporation,Newyork yang menjual kertas foto mau menjadi mitranya untuk mengembangkan temuannya.Haloid Company kemudian merubah nama mesin foto copy pertama electrogafi karena dianggap kurang memiliki nilai jual,lalu diusulkan dengan nama Xerography.Xerography menjadi komersial setelah diadopsi oleh Xerox Corporation.Salah satu produk awal Xerox adalah xerox 941,mesin foto copy pertama yang otomatis pertama yang menggunakan proses Xenography.Dinamai Xerox 941 untuk merujuk dalam kemampuan mesin dalam mengkopi kertas dengan ukuran 9 inci x 14 inci (229mm x 356mm).

Xerox 914,yang dapat mengkopi hingga 100 ribu kertas perbulan,sangat populer dikawasan masyarakat pada masa itu.Produk menyumbang pendapatan perusahaan hingga 60 juta dollar AS.Kesuksesan itu membuat perusahaan memutuskan merubah namanya dari Haloid menjadi Xerox pada 1958.Hingga kini xerox merupakan mesin foto copy dan printer terkemuka didunia.Produk yang dihasilkan perusahaan yang kini bermarkas di stamford,Conectticut,AS itu pada 2006 lalu berhasil membukukan pendapatan 15,9 miliar dolar AS.Jumlah karyawannya mencapai 53.700 orang tersebar didunia. Chester Carlson meninggal pada 9 september 1968,di Rochester,New York karena penyakit hati yang kronis.Berkat temuannya melalui mesin foto copy,chester carlson telah menemukan car yang merombak paradigma penulis ulangan sebuah dokument,hingga sekarang proses ini tidak dapat ditinggalkan dalamkehidupan modern hingga hari ini.

KOMPONEN MESIN FOTO COPY


Komponen Dasar Foto Copy

Exposure Lamp

Halogen Lamp

Lampu Halogen adalah lampu yang diisi dengan gas halogen ( yodium atau brom). Gas Halogen menekan penguapan kawat pijar yang menggunakan suatu proses regenerasi bahan kimia yang disebut “ perputaran halogen”. Halogen Lampu mempunyai umur efektif yang panjang dan keluaran cahayanya kuat.



Karakteristik Lampu Halogen

Distribusi spectrometric luas
Tingkatan Kekuatan penerangan tinggi
sinar stabil dari temperatur sumber cahaya dan hanya terjadi perubahan yang kecil
umur lampu yang panjang
Konsumsi Listrik besar
Keluaran Panas besar

Fluorescent Lamp

Fluorescent lamp adalah tabung kaca tertutup yang mempunyai electroda pada masing-masing ujungnya. pada permukaannya dilapisi suatu material mengandung fosfor. Tabung diisi dengan gas argon ( atau argon/krypton gas) yang dicampur dengan sejumlah kecil uap air raksa. Pada saat tegangan tinggi dialirkan maka electroda bereaksi, dan busur cahaya terbentuk dan mengionisasikan uap air air raksa . Air raksa yang terionisasi memancarkan radiasi ultra ungu, lalu membentur dinding kaca dan mengaktifkan fosfor pelapis, yang menyebabkan munculnya cahaya.
Karakteristik



Cahayanya tidak terlalu terang.
Hasil pemanasan dari kawat pijar.
Untuk penerangan jangka pendek.
Lapisan fosfor yang menentukan keluaran warna dari lampu tersebut.
Intensitas perubahan kekuatan penerangan tergantung pada temperatur tabung.
Kekuatan penerangan tidak seimbang pada bagian ujung tabung, maka memerlukan plat pembungkus.

Xenon Lamps

Lampu xenon adalah tabung lampu yang diisi dengan gas xenon. Ketika voltase dialirkan ke seberang terminal lampu, gas xenon diionisasikan dan arus mengalir sepanjang gas dengan pemacaran rendah. Terminal tidak harus dipanaskan dulu. tidak sama dengan lampu pendarfluor. Ada banyak macam lampu xenon. Lampu Xenon banyak digunakan pada mesin digital. output yellowish-green cahaya dengan puncaknya pada 543 nm. Lampu Xenon digunakan juga pada mesin copy warna. seperti lampu fluorescence juga yaitu memanfaatkan lecutan gas untuk menghasilkan cahaya putih.

Karakteristik

Cahaya tidak terlalu terang
Lebih murah dibanding fluorescent atau lampu halogen
Umurnya lebih panjang dan tidak mempunyai umur penggantian.
Panas rendah sehingga tidak memerlukan pendingin
Lebih ringkas dibanding fluorescent lamps .

LED Arrays

LED (light emitting diode) nama menyiratkan, suatu LED adalah suatu dioda yang memancarkan cahaya dengan arus listrik kecil . yang Biasanya digunakan sebagai alat indikator, tetapi mereka dapat juga digabungkan menjadi suatu array dan digunakan sebagai suatu sumber cahaya.

Karakteristik

LED array dapat di hubungkan dengan kable
Agar dapat diaktifkan masing masing atau per blok untuk menyediakan cahaya yang Presisi. LED array sangat berguna jika kita mebutuhkan Componen yang kompak.

Toner

Toner adalah kombinasi dari plastic resin, wax, Karbon dan partikel-partikel lain yang mempunyai karakteristik magnet.

Developer

Developer biasa juga disebut dengan carier atau stater. Gunanya untuk membawa toner ke drum/photoconductor.

Drum Charge

Di dalam ruang gelap charge corona memberikan tegangan Negatif ke permukaan Drum.

Exposure ( penyinaran )

Bayangan dari original di pantulkan ke drum melalui lensa yang membuat drum menghilangkan tegangan negatif.Pada bagian yang terkena sinar. Sedangkan yang tidak terkena sinar tetap mengandung tegangan negatif.

Erase ( penghapusan )

Penghapusan tegangan yang ada di Drum pada bagian yang tidak terpakai.

Development ( pembuatan )

Developement mengirimkan toner ke Laten image di drum yang Membuat drum mengandung toner.

Image Transfer ( pengiriman bayangan )

Bayangan yang ada di Drum di tranfer ke kertas yang telah diberikan tegangan negatif yang sangat tinggi sehingga bayangan yang ada di drum ada di kertas.

Cleaning ( pembersihan )

Karet pembersih membersihkan sisa toner yang ada di drum agar drum dapat dipergunakan kembali.

Quenching ( penetralan )

Lampu menyinari drum agar sisa sisa tegangan yang ada drum hilang dan membuat drum menjadi netral.


Daftar Kode Error Canon Ir5000/6000/5570/6570

Mesin Digital pada umumnya telah dilengkapi system memory dimana terdapat semua kode - kode kerusakan yang mengalamatkan ada gangguan pada sensor.CPU pada control utama dan CPU pada controler DC dimana tujuannya untuk mempermudah menganalisa dibagian mana yang sedang mengalami gangguan/kerusakan,berikut adalah daftar kode error serta daerah komponen yg bermasalah.

E- 000 
The main thermistor (TH1) has poor contact or an open circuit. The thermal switch (TP1) has an open circuit. The fixing heater has an open circuit. The SSR is faulty. The DC controller PCB is faulty.

E- 001

The main thermistor (TH1) has a short circuit. The sub thermistor (TH2)
has detected overheating. The SSR is faulty. The DC controller PCB is
faulty.

E- 002
The main thermistor (TH1) has poor contact or an open circuit. The thermal switch (TP1) has an open circuit. The SSR is faulty. The DC controller is faulty.

Mode of Detection
0000 The temperature of the upper fixing roller does not reach 100°C within 2 min after it has exceeded 70°C.Caution The error must be reset in service mode (COPIER>FUNCTION>
CLEAR>ERR).

E- 003
The main thermistor (TH1) has poor contact or an open circuit. The thermal switch (TP1) has an open circuit. The fixing heater has an open circuit. The SSR is faulty. The DC controller PCB is faulty.

Mode of Detection
 0000 The temperature detected by the main thermistor is 70°C for 2 secor more after it has reached 100°C. Caution The error must be reset in service mode (COPIER>FUNCTION>
CLEAR>ERR).

E- 004
The SSR has a short circuit. The DC controller PCB is faulty.

Mode of Detection    
 0000 The SSR used to drive the fixing heater is found to have a short circuit (hard circuit detection).Caution The error must be reset in service mode (COPIER>FUNCTION>
CLEAR>ERR).

E- 005
The fixing web has been taken up. The fixing web length sensor (PS45) is faulty. The DC controller PCB is faulty.

Mode of Detection       
0000 The length of fixing web that has been taken up is in excess of the specified length.
Caution After replacing the fixing web, be sure to reset the two web counters in service
mode: COPIER>COUNTER>MISC>FIX-WEB and COPIER> COUNTER>DRBL-1>FX-WEB.

E- 010
The main motor (M2) is faulty. The DC controller PCB is faulty.

Mode of Detection
0000 The clock pulses do not arrive for 2 secs or more after the main motor drive signal (MMFG) has been generated.

E- 012
The drum motor (M1) is faulty. The DC controller PCB is faulty.

Mode of Detection
0000 The clock pulses do not arrive for 2 secs or more after the drum motor drive signal (DMFG) has been generated.

CANON IR3300 KECIL-KECIL TAPI BANDEL


Mesin fotocopy Canon iR 3300  Diciptakan bagi anda usaha pemula serta pemakaian dikantor dengan skala menengah ( sedang ) type ini memiliki kecepatan copy 33 – 35 lembar dalam 1 menit, dan sudah dilengkapi beberapa fitur – fitur khas dari Canon, Canon image Runner digital seperti print, scan, mail box,  fax dan send to email, serta ketahanan dalam megerjakan tugas copy yang cukup lama. Dilihat dari sisi desain type iR3300 terbilang berdimensi medium ( sedang ) yang dilengkapi dengan layar monocrhome touch screen atau layar sentuh dan keypad tombol – tombol yang nyaman untuk ditekan dalam pengoperasian penggunaan mesin fotocopy ini.

Mesin fotocopy Canon iR 3300
Di Indonesia harga mesin type ini dibandrol dengan harga Rp. 15.000.000,- ( Rekondisi 90% ) sebuah harga yang pantas untuk mesin fotocopy berkecepatan 33 – 35 lembar permenit serta dilengkapi dengan fitur  – fitur canggih seperti : copy, print, scan ( B/W ), mail box dan send to email. Mesin fotocopy Type ini bisa dijadikan pilihan terbaik untuk anda yang baru memulai usaha copy center atau fotocopy dengan skala medium ( sedang ), dan  juga direkomendasikan untuk pemakaian dikantor yang membutuhkan pemakaian mesin yang berkecepatan medium ( sedang ). Canon iR3300 saat ini menjadi terlaris dan mesin terbanyak diminati bagi usaha pemula dan kantor.

Specifications

Main Unit Specs

Model Name imageRUNNER 3300
Type Digital Multifunction Imaging System
Imaging System Laser Dry Electrostatic Transfer
Developing System Dry Monocomponent Toner Projection
Fixing System RAPID Fusing System™
Duty Cycle Up to 120,000 impressions/month
Image Server Memory 128MB Standard + 5.1GB Hard Disk Drive
Max Mailboxes Supported 100
Max Copy Reservation 5 Jobs
Scanning Resolution 600 dpi x 600 dpi
Printing Resolution 600 dpi x 600 dpi
Interpolated Resolution 1200 dpi x 600 dpi (Copy)
2400 dpi x 600 dpi (Print)
Halftone 256 Gradations of Gray
Letter 33 cpm/ppm
Letter R 18 cpm/ppm
Legal 14 cpm/ppm
Ledger 16 cpm/ppm
Statement 18 cpm/ppm
First Copy Time 5.8 seconds (From Platen Glass)
6.6 seconds (From DADF)
Multiple Copies 1 to 999
Magnification 25% – 800%, in 1% increments
Preset Reductions 25%, 50%, 64%, 73%, 78%
Preset Enlargements 121%, 129%, 200%, 400%, 800%
Acceptable Originals Sheets, Books, 3 Dimensional Items (Up to 4.4 lbs.)
Maximum Original Size 11″ x 17″
Standard Paper Capacity 2 x 500 Sheets
Manual Bypass 50 Sheets
Maximum Paper Capacity 4,550 Sheets
Output Sizes
Cassette Statement to Ledger
Bypass 4″ x 5-1/2″ to 11-3/4″ x 17″
Acceptable Paper Weights
Cassette 17 – 20 lb. Bond
Bypass 17 – 32 lb. Bond
Duplexing Standard Automatic Trayless Duplexing
Warm Up Time 10 Seconds or Less
Exposure Control Automatic or Manual
Power Requirements 120V, 60Hz, 15A
Dimension 40-1/8″ x 22-1/4″ x 26-3/4″
(1020mm x 565mm x 678mm)
Weight 176.3 lbs.

Back to TopSupplies

Toner GPR-6 Black Toner
Estimated Toner Yield 15,000 Images (6% Coverage)
Drum GPR-6 Drum Unit
Estimated Drum Yield 55,000 Impressions

Back to TopAccessories

Feeders
Description Duplexing Automatic Document Feeder-H1 (Optional)
Acceptable Originals Statement to Ledger
Scanning Speed 33 opm (Letter)
Capacity 50 Sheets
Paper Weights 10 – 32 lb. Bond
Different Size Originals Same Width/Different Width
Power Source Directly from Main Unit
Dimensions 4-7/8″ x 22-3/8″ x 21-1/8″
(122mm x 565mm x 535mm)
Weight 17.6 lbs.
Paper Supply Options
Description Cassette Feeding Unit-W1 (Optional)
Number Of Cassettes 2
Paper Capacity 1,000 Sheets
Paper Sizes Statement-R to Ledger
Paper Weights 17 – 20 lb. Bond
Power Source Directly from Main Unit
Dimensions 22-3/8″ x 26-3/4″ x 9-3/4″
(565mm x 678mm x 248mm)
Weight 67.1 lbs.
Description Paper Deck-L1 (Optional)
Number Of Cassettes 1
Paper Capacity 2,500 Sheets
Paper Sizes Letter
Paper Weights 17 – 20 lb. Bond
Power Source Directly from Main Unit
Dimensions 17″ x 12-7/8″ x 23-1/4″
(432mm x 324mm x 591mm)
Weight 66.1 lbs.
Output Options
Finishers Output Trays
Description Finisher-J1 (Optional)
Paper Weights 17 – 32 lb. Bond
Paper Size Statement to Ledger
Number Of Trays 1
Top Tray 300 Sheets (Letter)
Staple Capacity 30 Sheets (Letter)
15 Sheets (Ledger)
Staple Positions 1-Top Corner
Power Source Directly from Main Unit
Dimensions 9-1/8″ x 22-3/8″ x 20-1/8″
(232mm x 565mm x 509mm)
Weight 24.2 lbs.
Description Inner 2-Way Tray-A1 (Optional)
Paper Weights 17 – 32 lb. Bond
Paper Size Statement to Ledger
Number Of Trays 2
Top Tray 100 Sheets (Letter)
Lower Tray 250 Sheets (Letter)
Power Source Directly from Main Unit
Dimensions 10″ x 5-7/8″ x 16-1/2″
(254mm x 149mm x 420mm)
Weight 7.7 lbs.
Description Saddle Finisher-G1 (Optional)
Paper Weights 17 – 32 lb. Bond
Paper Size Statement to Ledger
Number Of Trays 4 Trays, including Saddle-Stitch Tray and Inner 2-Way Tray
Top Tray 1,000 Sheets (Letter)
Middle Tray 250 Sheets (Letter)
Lower Tray 250 Sheets (Letter)
Saddle Stitch Tray 100 Sheets
Staple Capacity 50 Sheets (Letter)
Staple Positions Multiposition Stapling
1 – Top Corner
2 – Side Margin (Book Staple, Two Patterns)
3 – Saddle-Stitch
Paper Sizes Letter-R , Ledger
Stapling Capacity 10 sheets
Fold Type V-Fold Standard
Power Source Directly from Main Unit
Dimensions 33-5/8″ x 21″ x 23-3/4″
(855mm x 532mm x 603mm)
Weight 77.2 lbs.
Description Puncher Unit-K1 (Optional)
Paper Weights 17 – 32 lb. Bond
Paper Size Letter, Legal, Ledger
Hole Punch 2 Holes (Letter-R. Legal)
3 Holes (Letter, Ledger)
Power Source Directly from Main Unit
Dimensions 6-3/4″ x 3-1/2″ x 22-1/8″
(170mm x 90mm x 560mm)
Weight 5.3 lbs.
Fax Board
Description Super G3 Fax Board-J1 (Optional)
Applicable Line Public Switched Telephone Network
Compatibility G3
Modem Speed 33,600 bps
Transmission Speed 3 Seconds
Data Compression MMR, MR, MH, JBIG
Memory 128MB
Maximum Memory 128MB
Print Board
Description Network Multi-PDL Printer Kit-C1 (Optional)
Processor 250 MHz Canon Custom Processor
Standard Memory 128MB RAM
Maximum Memory 128MB RAM
Hard Disk 5.1 GB
Continuous Print Speed 33 ppm (Letter)
PDL Support PCL 5e, PCL 6, PostScript 3 Emulation
Postscript Fonts 136 (117 Adobe Type Fonts, 19 True Type)
PCL Fonts 80 Roman, 32 Barcode
Interface Connections Ethernet (10/100BaseT)
IEEE 1284 (Parallel)
Token Ring (Optional)
Other Features Access to Full Finishing Features
Internet Connectivity
NetSpot Supported
Spooling Supported